Govoni

Allows for the assembly/disassembly of the brake caliper fixing screws when working on the braking system. Used mainly on the front and rear axles of heavy vehicles. Even the most stubborn screws are released with the blow of a hammer on the end of the wrench. All wrenches are equipped with a ¾" square drive that also allows clamping, in combination with a torque wrench, according to the manufacturer's instructions. Warning: pay attention to the torque conversion formula marked on the wrench by means of a laser (necessary because of the lever's extension due to the type of construction). It is no longer necessary to remove the lever of the steering control tie rod.   Application: MB Atego, Actros/Kässbohrer Bus   Technical data: Length: 220mm 6-side profile

Read more less

Easy fitting and mounting of wheels Especially dedicated for cars with short axle tie with free turning brake disc without centering screw Bolts are placed into the wheel bolt holes Very quick mounting without any thread For wheel bolts M12 and M14 Advantages:  1.   Free mounting of the wheel locking boltsThe full weight is resting on the centering bolts which allows for 2.  No risk of heavy wheels falling; decreasing the likelihood of injury to the operator Contents: 1 x Fit up bolt M12 x 127.5 mm1 x Fit up bolt M14 x 127.5 mm2 x Replacement sleeve M12 x 27.8 mm2 x Replacement sleeve M14 x 27.8 mm1 x support

Read more less

Use this tool kit to remove and refit slotted bushes properly. The slight conical grinding makes it possible to extract and reuse bushes without damage. The tools may be fit directly on the vehicle without removing entire axes components. Pressers may also be used on the workshop press. By means of the locking device and relating half-shells, bushes are pre-tensioned carefully and parallel to one another so they can be pressed easily into their seat. While the bush is often damaged using commercial tapered sockets, the assembly operations do not damage/deform/detach the bearing's cover when this locking device system is used. The half-shells are fixed securely inside the locking device so they will not slip out. The kit includes a wide selection of the most common applications with high market coverage. Other half-shell kits will soon follow to ensure the subsequent removal of the system. Due to the partly enormous forces required especially for removal, the kit includes GO1012 12T Hydraulic cylinder , which is optimal for integrations.   20017000 Hand Operated Hydraulic Aluminium Pump is required in order to operate the kit Application Ø 75mm MB Actros (stabilizer) Ø 70mm MAN Ø 68mm MAN (front spring) ROR, SAF Ø 66mm IVECO Eurostar (driver’s cabin) Ø 65mm MB Actros (stabilizer), Atego Ø 63mm DAF Ø 60mm MB/IVECO Eurostar (stabilizer), Renault Kerax, Magnum, Premium (leaf spring eye) Ø 58mm MB 3229 B, 652, 650/Volvo Ø 56mm IVECO Eurostar (driver’s cabin)

Read more less

To loosen and tighten fuel filters and oil filters. The wrench is equipped with 2 extension half-shells (toothed on the inside), which are attached directly to the jaws of the filter wrench and can be secured in place. It can be used with or without extensions. Can be used for filters with and without guide profiles Ø 60-80 with extension

Read more less

Technical data: 6-teeth - tooth width 10 mm Inner Ø 110 mm - Sq 1” Applications: Low-platform bus with gantry axle HDNP-1300 Suitable for MAN AUTOBUS

Read more less

Allows for the assembly/disassembly of the brake caliper fixing screws when working on the braking system. Used mainly on the front and rear axles of heavy vehicles. Even the most stubborn screws are released with the blow of a hammer on the end of the wrench. All wrenches are equipped with a ¾" square drive that also allows clamping, in combination with a torque wrench, according to the manufacturer's instructions. Warning: pay attention to the torque conversion formula marked on the wrench by means of a laser (necessary because of the lever's extension due to the type of construction). It is no longer necessary to remove the lever of the steering control tie rod.   Application: MAN TGL Technical data: Length: 219mm Hex profile

Read more less

Allows for the assembly/disassembly of the brake caliper fixing screws when working on the braking system. Used mainly on the front and rear axles of heavy vehicles. Even the most stubborn screws are released with the blow of a hammer on the end of the wrench. All wrenches are equipped with a ¾" square drive that also allows clamping, in combination with a torque wrench, according to the manufacturer's instructions. Warning: pay attention to the torque conversion formula marked on the wrench by means of a laser (necessary because of the lever's extension due to the type of construction). It is no longer necessary to remove the lever of the steering control tie rod.   Application: MB Atego/Actros, SAF Technical data: Length: 219mm Bi-hex profile

Read more less

This tool is universally used for light and heavy diesel engines, this tool allows you to professionally restore the thread of the NOx sensor hole without damaging the exhaust system.  The tool is equipped with an alignment guide at the front of the male threader to ensure a correct angle. With an extra short body, the tool can be used with a socket wrench or ratchet wrench in tight spaces. Optimal for cleaning and regenerating threads up to the end of the thread/stop blind hole. Application Audi, Vw, Porsche, Opel, Mercedes-Benz, Bmw, General Motors, Man Technical data Square Drive: SW 13 mm Length: 50 mm Tensioning grooves: 6 Material: HSCO

Read more less

Application Citroen, Opel, Peugeot, Toyota: 9819074780, SU001 A6528 FAG: 713 6506 80 SKF: VKBA 7120

Read more less

Locking Pliers supplied with 4 sets of interchangeable clamps for tightening the snap ring on the transmission shaft.  There pliers ensure mounting without risk of damage to the rush (clips) of the teeth when inserting the bowl on the transmission shaft.  Includes:  1 x Pliers 2 x Ø23.8mm half shell 2x Ø24.6mm half shell  2x Ø26.9mm half shell 2x Ø28.5mm half shell

Read more less

Tool to removeal Bosch magnetic injectors.  Removal is carried out without partial disassembly, so reuse is ensured.  Allows for the injector to be removed without removing the injector solenoid or internal components. 

Read more less

They allow for the assembly/disassembly of the brake caliper fixing screws when working on the braking system. Used mainly on the front and rear axles of heavy vehicles. Even the most stubborn screws are released with the blow of a hammer on the end of the wrench. All wrenches are equipped with a ¾" square drive that also allows clamping, in combination with a torque wrench, according to the manufacturer's instructions. It is no longer necessary to remove the lever of the steering control tie rod.  Application: MB Atego, Actros/Kässbohrer Bus  Technical data: Length: 220mm 6-side profile

Read more less

Technical data: CH. 41 mm  Octagonal 80,5mm   Application: Suitable for SCANIA

Read more less

Technical data: 6-teeth - tooth width 13 mm Inner Ø 76,5 mm -  Sq 3/4”   Application: Front axle models: M3 - ME - MI Rear axle modelswith outer planetary unit: 3MR - 5MR Suitable for MAN

Read more less

Due to the particular shape of the arms, these pliers allow you to easily open and close CAILLAU CLIC (55, 66, 86), CLIC R (R66, R86, R96) and CLIC E clamps With these pliers it is possible to open and close screwless hose clamps It is possible to change from the opening to the closing function by rotating the pliers 180° Ergonomic, self-opening handles with different colours to identify the opening and closing functions For vehicle engine and chassis, fuel lines, air filters, steering, drive shaft sleeves, as well as other industrial and electrical sectors

Read more less

It is possible to remove the drive shaft inserted in the gearbox, with the use of this tool Insert the tool between the drive shaft and gearbox. Then, with a slight slide hammer hit, the fixing circlip, found in the gearbox, is broken The difficult position of the fixing circlip is avoided by the forks central traction, allowing the user to easily unlock the drive shaft

Read more less

GO3041 -  Electro-Hydraulic 2 Post Lift - 4 Tonne Features: 2 Hydraulic cylinders Safety valves to prevent overloads Descent velocity controlled by hydraulic valve Extended adjustment of arms Shut off bar to prevent damage caused by high lifting vehicles Mechanical foot protection Three stage arms

Read more less

GO3040 - Symmetric Electro-Hydraulic 2 Post Lift with Base Frame - 4 Tonne Features: 2 Hydraulic cylinders Wedge release through electromagnet Automatic locking of arms Overload hydraulic safety device automatic control unit Automatic release of the safety devices during the descent phase Dead man controls 24V Lowering valve with manual descent  

Read more less

Replacement ferrite for 581000042 - Induction Heater Wand Compatible with: GO1472 - Induction Heater with Inverter 8KW GO1473 - Induction Heater with Inverter 5KW 3 Phase GO1474 - Induction Heater 3.5kw  GO1475 - Induction Heater with Inverter 5KW Single Phase

Read more less

Induction heater wand Compatible with: GO1472 - Induction Heater with Inverter 8KW GO1473 - Induction Heater with Inverter 5KW 3 Phase GO1474 - Induction Heater 3.5kw  GO1475 - Induction Heater with Inverter 5KW Single Phase   For spare ferrite see 581000043

Read more less

Special tip induction heater wand Compatible with: GO1472 - Induction Heater with Inverter 8KW GO1473 - Induction Heater with Inverter 5KW 3 Phase GO1474 - Induction Heater 3.5kw  GO1475 - Induction Heater with Inverter 5KW Single Phase

Read more less

Induction heater wand   Compatible with: GO1471 - Induction Heater with Inverter 13KW   For spare ferrite see 

Read more less

Replacement ferrite for 581000040 Induction heater wand Compatible with: GO1472 - Induction Heater with Inverter 8KW GO1473 - Induction Heater with Inverter 5KW 3 Phase GO1474 - Induction Heater 3.5kw  GO1475 - Induction Heater with Inverter 5KW Single Phase  

Read more less

Induction heater wand Compatible with: GO1472 - Induction Heater with Inverter 8KW GO1473 - Induction Heater with Inverter 5KW 3 Phase GO1474 - Induction Heater 3.5kw  GO1475 - Induction Heater with Inverter 5KW Single Phase   For spare ferrite see 

Read more less

Replacement ferrite for use with 581000038 Induction heater wand Compatible with: GO1472 - Induction Heater with Inverter 8KW GO1473 - Induction Heater with Inverter 5KW 3 Phase GO1474 - Induction Heater 3.5kw  GO1475 - Induction Heater with Inverter 5KW Single Phase  

Read more less

Special tip induction heater wand Compatible with: GO1470 - Induction Heater with Inverter 18KW

Read more less

Special tip induction heater wand Compatible with: GO1470 - Induction Heater with Inverter 18KW   

Read more less

Replacement ferrite for use with 581000025 Induction heater wand   Compatible with: GO1471 - Induction Heater with Inverter 13KW

Read more less

Replacement ferrite for use with 581000021 Standard wand with round head   Compatible with: GO1470 - Induction Heater with Inverter 18KW GO1471 - Induction Heater with Inverter 13KW

Read more less

Induction heater wand  - round head Compatible with: GO1470 - Induction Heater with Inverter 18KW GO1471 - Induction Heater with Inverter 13KW   For spare ferrite see 581000022

Read more less

Replacement ferrite for 581000019 - Induction Heater Wand Compatible with:  GO1471 - Induction Heater

Read more less

Standard tip induction heater wand Compatible with GO1471 - Induction Heater with Inverter 13KW   For spare ferrite see 581000020

Read more less

Wheeled Mobile lift, with a capacity of 2000 kg, and an opening, adjustable and oscillating lifting surface, which allows easy access under the vehicle for dismantling battery packs, engines, and transmissions. The upper platform is equipped with M8 threaded holes, for fixing the battery, engine and gearbox support kits. The new GO2000TR-E is provided with a control unit integrated into the base, allowing you to choose the desired height via a mobile button panel equipped with a magnet. This allows to raise and lower the platform in a safe and precise way and precise management of the fixing points of the battery or other mechanical components, such as engines and gearboxes. Thanks to its high lifting capacity, it can be used for truck and commercial vehicle battery packs, as well as particularly heavy mechanical components. Thanks to the large-capacity structure and the double reinforced scissors, it guarantees lifting and weight management capacity, without balance problems.  Extendable range handle (incl. 2x hand wheels for fixation) Platform extendable (extension and access to the centre) (incl. handle and 2x hand wheels for fixation) Platform laterally adjustable by 40 mm (access for adjustment from left and right without the need to move the table out from the vehicle underbody) Inclination of the platform ±2° adjustable (compensation to lifting platform/floor inclination) Platform with threaded housings for support adapters or special solutions Lifting and lowering by electro-hydraulic pump with remote control system   Technical Data: Extendable Table  200 mm  Tilting Table  ± 2°  Shifting Table ± 40mm Extendable Range Handle 200mm Max. capacity  Max 2000 kg Lifting time  38 s (no load) / 42 s ( full load) Lowering time   90 s (no load) / 20 s (full load) Power supply  380 Volt  Three-phase motor   1,1 Kw  

Read more less

Wheeled Mobile lifting table, with a capacity of 1000 kg, and an opening, adjustable and oscillating lifting surface, which allows easy access under the vehicle for dismantling battery packs, engines, and transmissions. The upper platform is furnished with M8 holes for fixing the battery, engine, and gearbox support kits. The new GO1000BR-E is provided with a control unit integrated into the base, allowing you to choose the desired height via a mobile button panel equipped with a magnet. This allows you to raise and lower the platform in a safe and precise way and precise management of the fixing points of the battery or other mechanical components, such as engines and gearboxes. Thanks to its high lifting capacity, it can be used also for truck and commercial vehicle battery packs, as well as particularly heavy mechanical components. Platform centre section removable (grants access to the centre) Inclination of the platform ±2° adjustable (compensation to the lifting platform/floor inclination) Platform with threaded holes for support adapters as well as vehicle specific special solutions  Lifting and lowering via remote control Technical Data Modular opening table  1/3 = 420 mm  Tilting table  ± 2° (angle) Max. capacity  Max 1.000 kg Lifting time  38 s (no load) / 42 s ( full load) Lowering time   90 s (no load) / 20 s (full load) Power supply  380 Volt (220 optional) Three-phase motor   1,1 Kw

Read more less

Digital electronic tester for checking the analog and PWM signals of sensors and activating various types of electro-mechanical actuators. A single instrument that contains infinite functions: the test and diagnosis capabilities of SPECTRUM are so broad and diversified that there is no comparison to any other device on the market. TECHNICAL DATA Ambient temperature range 0 - 45 °C Power supply directly from the battery 9-28V dc CABLES INCLUDED IN KIT GO2101 PWM Multimeter Wiring GO2102 Ground Test Wiring GO2103 Pulse Sense Wiring GO2104 DC Volt Generator Wiring GO2105 Resistor Sensor Wiring GO2106 PWM Power Wiring Plug-Croc Clip Wiring JACK wiring  GO2109 - PWM Power Plus (5 Pin) Wiring GO2110 - PWM Signal Wiring GO2111 - Piezo Activator Wiring GO2112 - Glow Plug Test Wiring GO2113 - OHM Meter Wiring GO2114 - Diagnostic CAN Wiring

Read more less

Optional cable kit in foam to upgrade GO2100PRO2  Contents: GO2109 - PWM Power Plus (5 Pin) Wiring GO2110 - PWM Signal Wiring GO2111 - Piezo Activator Wiring GO2112 - Glow Plug Test Wiring GO2113 - OHM Meter Wiring GO2114 - Diagnostic CAN Wiring All cables are available as individual parts.

Read more less

Digital electronic tester for checking the analog and PWM signals of sensors and activating various types of electro-mechanical actuators. A single instrument that contains infinite functions: the test and diagnosis capabilities of SPECTRUM are so broad and diversified that there is no comparison to any other device on the market. TECHNICAL DATA Ambient temperature range 0 - 45 °C Power supply directly from the battery 9-28V dc CABLES INCLUDED IN KIT GO2101 PWM Multimeter Wiring GO2102 Ground Test Wiring GO2103 Pulse Sense Wiring GO2104 DC Volt Generator Wiring GO2105 Resistor Sensor Wiring GO2106 PWM Power Wiring Plug-Croc Clip Wiring JACK wiring  Optional lead kit available GO2120 - – Sykes Pickavant (see kit page for individual lead details)

Read more less

4 Tonne electro hydraulic, mid raise scissor lift for tyre and car body shops. Features Overload safety valve Safety valve in case of sudden loss of pressure Descent speed control valve "Dead man" controls 24V Safety control on last descent segment "Buzzer" on last portion of descent Integrated lubrication system Easy to handle drive on and drive off ramps Hydraulically synchronized platforms Technical Data Lifting capacity: 4000 Kg Lifting Height: 117 - 1942 mm Platform Length: 1485 - 2285 mm Platform Width: 660 mm Total Width: 2220 mm Distance between Platform: 900 mm Power: 2.2 kW Voltage: 380-415V 50hZ Lifting Time: ≤ 50 s Lowering Time: ≥ 20 s Noise Level: ≤75 dB

Read more less

3.5 Tonne hydraulic, extra low profile double scissor lift. Features Overload safety valve Safety valve in case of sudden loss of pressure Descent speed control valve "Dead man" controls 24V Set of 4 rubber pads "Buzzer" on last portion of descent Technical Data Lifting capacity: 3500 Kg Lifting Height: 105 - 1930 mm Platform Length: 1485 mm Total Length: 2105 mm Platform Width: 660 mm Total Width: 2320 mm Distance between Platform: 900 mm Power: 2.2 kW Voltage: 380-415V 50hZ Lifting Time: ≤ 50 s Lowering Time: ≥ 20 s Noise Level: ≤75 dB

Read more less

3.5 Tonne electro hydraulic, mid raise scissor lift for tyre and car body shops. Features Overload safety valve Safety valve in case of sudden loss of pressure Descent speed control valve "Dead man" controls 24V Safety control on last descent segment "Buzzer" on last portion of descent Integrated lubrication system Easy to handle drive on and drive off ramps Hydraulically synchronized platforms Technical Data Lifting capacity: 3500 Kg Lifting Height: 105 - 960 mm Platform Length: 1400 - 2015 mm Platform Width: 480 mm Total Width: 1920 (2020) mm Distance between Platform: 900 (1000) mm Power: 3.2 kW Voltage: 380-415V 50hZ Lifting Time: ≤ 50 s Lowering Time: ≥ 20 s Noise Level: ≤75 dB

Read more less

25 Tonne heavy duty hydraulic trolley jacks with pneumatic wheels, for lifting great loads. 25 Tonne capacity Removable handle for quick and easy transport Equipped with automatic end stroke valve and overload valve Pedal for quick approach Pedal descent control Wide base plate support Auxiliary pneumatic wheels      

Read more less

18 Tonne heavy duty hydraulic trolley jacks with pneumatic wheels, for lifting great loads. 18 Tonne capacity Removable handle for quick and easy transport Equipped with automatic end stroke valve and overload valve Pedal for quick approach Pedal descent control Wide base plate support Auxiliary pneumatic wheels      

Read more less

Hydraulic trolley jacks for lifting small and medium loads. Thanks to the double frontal balancing rolls and to the rear turning wheels in polyurethane, these jacks can be moved on rough floors including grates, making them ideal for use during breakdown services. 2.5 Tonne capacity Ergonomic handle Double WULKOLLAN® wheels, suitable for use on rough flooring including grates    

Read more less

Hydraulic trolley jacks for lifting small and medium loads. Thanks to the double frontal balancing rolls and to the rear turning wheels in polyurethane, these jacks can be moved on rough floors including grates, making them ideal for use during breakdown services. 2.5 Tonne capacity Ergonomic handle Double WULKOLLAN® wheels, suitable for use on rough flooring including grates    

Read more less

Hydraulic trolley jacks for lifting small and medium loads. 2.5 Tonne capacity Ergonomic handle Single WULKOLLAN® wheels, suitable for use on rough flooring including grates    

Read more less

Hydraulic trolley jacks for lifting small and medium loads. 1.5 Tonne capacity Ergonomic handle Single WULKOLLAN® wheels, suitable for use on rough flooring including grates    

Read more less

15 Tonne pneumatic transmission jack to remove and install engines, gearboxes, and other heavy parts. for use with compressed air 7-10 bar pressure, supplied with a specific remote control.   1 chrome plated piston Two pedal pump, one for quick approach, one for use during the working phase Man-present release lever Descent control knob Overload valve Retractable wheels under 900Kg load Max height 2150mm    

Read more less