Govoni
GO324 - Mercedes C Bracket
Application: Mercedes: Class C starting from 2010.
GO2118PRO - Petrol Injector Test Bench
For use with Govoni Spectrum (GO2100Pro or GO2100Pro-X) Combined with SPECTRUM pro and its dedicated functions and strategies, it makes diagnostics, cleaning and flow control of fuel injectors easy, fast and above all within everyone's reach. The small size allows the injector test bench to be positioned on a shelf but without taking up too much space, and also makes it transportable despite its structural sturdiness. Safe both for the environment and for the operator himself, as the use of electricity is not directly required. Possibility to test up to 4 injectors simultaneously Suitable for any petrol injector Compressed air supply with adjustable pressure from 0 to 5 bar (72.5PSI-500 Kpa) Sliding injector holder rail with quick coupling adjustable in height with taps to be able to open or close the passage of the liquid for each injector Graduated burettes for immediate reading of the injectors flow rate Quick connection burettes Integrated flushing liquid tank with filler cap with maximum capacity of 2000 c.c. (2 liters) Quick release air hose Test bench dimensions L=max454 x H=685 x D=300mm The configuration consists of: test bench docking station cover
GO2115 - Docking Station Spectrum
Docking station for GO2100PRO
GO2114 - Diagnostic Can Test
Diagnostic wiring, with the function of analyzing the vehicle's CAN network through the self-diagnosis connector with display of the values and outcome of the test. For use with GO2100PRO
GO2113 - OHM Meter Wiring
Acquisition wiring, with resistance detection function for use with GO2100PRO
GO2112 - Glow Plug Test Wiring
Emulation wiring, with the glow plug test function with the measurement of the current absorption of the same and display of the tests.
GO2111 - Piezo Activator
Module with the function of activating the piezoelectric injectors, connecting to SPECTRUM, then it is recognized and is ready for activation.
GO2110 - PWM Signal
Emulation wiring, with the function of generating PWM waveforms with negative ground, for the emulation of sensors with digital output or the control of electronic low power actuators.
GO2109 - PWM Power Plus (5 Pin)
Emulation / acquisition wiring, with the function of PWM power generator such as PWM POWER with an integrated 5V voltage generator; mass generator and feedback control. It is used for the activation of the components controlled in feedback through potentiometers.
GO1503 - Battery Lifting Accessory Kit
Required to hold battery pack, engine or transmission on the platform, safely. The components fit perfectly to the different types of batteries, taking into consideration the possible specifications of the manufacturer. Slotted holes in the foot allow easy changing/moving of the platform. The support columns are height-adjustable and have a thread for screwing the rubbers/spacers. Used for platforms with M8 and M10 threaded holes. Specifications: Support foot length: 200 mm Minimum height: 215 mm Maximum height: 315 mm Usable key for upper pin: SW32 mm Threads used for top fixing: M8 Maximum capacity for each support: 100 Kg Fixing screw: M8 Fixing screw: M10
GO1127 - Locking Wiper Puller with Hammerhead
Required to remove the wiper arm from the wiper arm shaft. The special design with an adjustable fork width (spring mechanism) and narrow fork ensures high model coverage and good access even in confined spaces. Puller spindle with movable pressure head, meaning no damage to the wiper arm shaft.
GO076 - Gerridae Quick Connector Release Tool
Special tool to release/open quick-couplings with double-click lock (2 buttons). This product is equipped with two different sized tool heads, with the longer tool head including a joint for better access. Universally applicable for fuel quick-couplings on cars, vans, trucks, etc. Technical data Total Length: 198 mm
GO066 - Universal Hub Puller & Drive Shaft Kit
Preserve components i.e. wheel bearings, silent blocks and ball joints by using this kit for assembly and disassembly procedures. Optimized hole pitch for maximum coverage of models within the market (suitable for 2, 3, 4, 5 and 6-hole bolt pitch on hubs mounted on passenger cars). Includes the new dimension M14x1.25 of pull rod/extension for BMW. Applications Include: Extraction of the CV joint with spindle Disconnection of the CV joint with 1,5 Kg slide hammer (GO406 - 1,5Kg slide hammer not supplied) Extraction of the wheel hubs with a 9 Kg slide hammer (GO520 - 9Kg slide hammer not supplied) Assembly of the CV joints with a spindle Extraction with impact spindle
GO012 - CV Joint & Drive Shaft Extraction Set
Kit for the extraction of seized and blocked transmission shafts. Includes a flange with multiple holes to ensure greater coverage of the models on the market: suitable for hubs with 2, 3, 4, 5 and 6 holes or bolts. Can be used on a range of vehicles from cars to commercial vehicles. Extremely suitable for stuck transmissions shafts on VW/Mazda/Ford Models. Components: 1 x extractor 1-1 / 2 “-16G 1 x adapter for pushing screw 1-1 / 2 “-16G x M22x2.0 1 x thrust screw M22x2.0 1 x flange, 96-142 mm for 3, 4, 5 and 6- holes, or bolts of size M12 / M14 5 x conical washer H = 5 mm 6 x conical spacers H = 25 mm 1 x impact screw 1 x handle for impact screw Technical data: For holes / Bolts: M12 and M14 Working range: M12: Ø96-138 mm / M14: Ø98-136 mm
GO415 - Diesel Injector Seat Cleaning and Milling Set
• Kit to be used for removing the combustion residues that remain in the injectors seat without any damage • For cleaning and maintaining the injector shaft • Flawless removal of carbon deposits to create a spotless surface on the sealing ring in the cylinder head • Basic unit can be adapted to injector shaft; spring-assisted adjustment of contact pressure • Special carbide cleaning cutter • Precise centring Components: 4 x Sealing plugs 2 x Brass brushes for cleaning the injector nozzle housing 1 x Cotton pad set (10pcs) 2 x Brush for cleaning the sealing seat 4 x Nylon brushes for cleaning the injector seat - Ø18-19-21-24mm 4 x Brass brushes for cleaning the injector seat - Ø18-19-21-24mm 1 x Flexible extension 4 x milling cutters for sealing seat 1 x Brush with brass fibres
GO561 - Injector Removal Kit - Bosch Ducato Diesel Engine 3.0
Complete tool for the removal of Bosch Piezo injectors. Removal is carried out with partial disassembly and this ensures that the injector can be reused. Appliction: Fiat Ducato 3.0 L Diesel from 2006 Iveco Daily 2.3 L from 2011 to 2014 3.0 L Diesel from 2007 Citroen Jumper 3.0 L HDI from 2010 Peugeot Boxer 3.0 L HDI from 2010 Injectors: 0445116059 0445116019
GO449 - Slide Hammer Injector Removal Set
Now includes new adapters for CR connector M12x1.5 and M14x1.5 This operation may be carried out without disassembling the injector head. This Kit allows injector removal with three distinct procedures: 1. Using the pliers with holding arms perfectly fitting to the shape of the injector 2. Using the articulated joint adapter and the pivot, that has to be screwed to the fitting of the Common Rail duct 3. Using the special socket (for Bosch CR) that ensures the removal of the injector without removing the electrical connection plastic top, the injector remains intacts and working after removal. Applications: Denso, Bosch, Siemens
GO354 - Ball Joint Bi-Hex Socket 32mm For Ford
Special socket with specific dimensions for professional dismantling the axle nut.Damage/Jamming on the outer profile nut will be prevented due to the high accuracy of the fit.Application: C-MAX ENERGI 2014-2018 C MAX 2018-2019 FOCUS from 2018 KUGA from 2017 MUSTANG from 2015 CONNECT Mk2 and TURNEO CONNECT from 2017 Etc. For OEM no. Axle Nut Ford 2 216 529 (M22x1.5) Technical specifications: Drive 1/2" + hexagon SW30 Profile hexagon SW31.5 mm Total length 50mm
GO316 - Macpherson Strut Support for use with Transmission Jack
Can be used to support the shock absorber when the suspension arm is removed. The shock absorber support is used together with a standard transmission jack. It is used to prevent the shock absorber from sinking when removed from the handlebar arm. Includes: Macpherson Strut Support Safety brack 80mm Reduction for strut support 60mm Ø25mm adapter Ø30mm adapter Capacity: 120KG
GO1354 - Hub Nut Socket - MB Sprinter
Loosen the nut of the rear reduction hypoid axle Rear axle models: HL0/3 - HL0/6 - HL0/7 - HL1/2 - HL1/3 - HL1/8 - HL1/9 - HL2/2 - HL2/3 - HL2/5 HL2/9 - HL2/11 - HL2/12 - HL2/15 Specific for MERCEDES SPRINTER - 412T - VW - LT Dimensions: 6 teeth - tooth width 7.5 mm - inner Ø 63 mm
GO1350 - Hub Nut Socket - Iveco
Technical data: CH. 90 mm - Sq 1” Application: Suitable for IVECO
GO1349 - Hub Nut Socket - Renault
Technical data: CH. 105 mm - Sq 1” Application: Suitable for IRISBUS, VOLVO
GO1348 - Hub Nut Socket - Renault
Technical data: CH. 105 mm - H. 57 mm - Sq 1” Application: Suitable for RENAULT
GO1346 - Hub Nut Socket - Renault
Technical data: 4-teeth - tooth width 13,5 mm - Sq 1” Application: Suitable for RENAULT
GO1345 - Hub Nut Socket - Renault
Technical data: CH. 115,7 mm - depth 45 mm - Sq 1" Application: Suitable for RENAULT
GO1344 - Hub Nut Socket - Volvo/ Renault/ Fiat
Technical data: CH. 95 mm - depth 28 mm - Sq 1” Application: Suitable for RENAULT, VOLVO, FIAT
GO1343 - Hub Nut Socket - Renault
Technical data: CH. 80 mm - depth 16 mm - Sq 1” Application: Suitable for RENAULT
GO1342 - Hub Nut Socket - Renault
Technical data: CH. 80 mm - depth 23 mm - Sq 1” Application: Suitable for RENAULT BUS, EUROCARGO, EUROTECH
GO1341 - Hub Nut Socket - Renault
Technical data: CH. Ø 77 mm - Sq 1"
GO1340 - Hub Nut Socket - Man
Technical data: 6-teeth - tooth width 10 mm Inner Ø 110 mm - Sq 1” Applications: Low-platform bus with gantry axle HDNP-1300 Suitable for MAN AUTOBUS
GO1338 - Hub Nut Socket - BPW
Technical data: Inner Ø 74 mm - Sq 1” Application: Suitable for BPW 12TN
GO1337 - Hub Nut Socket - BPW
Technical data: Inner Ø 90 mm - Sq 1” Application: Suitable for BPW 9TN
GO1336 - Hub Nut Socket - MAN/Mercedes
Technical data: 60x76 mm - Sq 1” Application: Front axle models: SK VL5/1 D9-2629 in 6x4. 2635 in 6x4. 3535K 8x4 Suitable for MERCEDES, MAN
GO1335 - Hub Nut Socket - DAF/Mercedes
Technical data: 56x71 mm - Sq 1” Application: Axle models KÄSSBOHRER/SETRA: front axle 6,5 and 7,5t of type S 210 and 215, SG 219-221 and dead axle types S 216 HDS and S 228 DT types 0303, 0305-G and 0307 Axle models DAF, Mercedes: VL 3/8, 4/7, 4/9, 4/15, VD 4/14, of type 363, 385, 387, 389, 391, 393, 395, 617, 620, 621, 622, 623, 625, 649 Axle models Mercedes - Bus: VO 3/10, 4/11, 4/13 and 4/19 of type 0303, 0305-G and 0307
GO1334 - Hub Nut Socket - Hexagonal - Fruehauf
Technical data: Ø 123 mm Hexagon 110 mm Application: Suitable for FRUEHAUF
GO1333 - Hub Nut Socket - Polygonal - R.O.R.
Technical data; Octagon 84 mm Ø 83 mm Application: Suitable for R.O.R.
GO1332 - Hub Nut Socket - Scania
Technical data: 4-teeth - tooth width 7,6 mm Inner Ø 91 mm - Sq 1” Application: Rear axle Suitable for SCANIA
GO1331 - Hub Nut Socket - Mercedes
Technical data: 6-teeth - tooth width 10 mm Inner Ø 75 mm - Sq 3/4” Application Rear axle models: HL2/14, HL2/30, KL2/16, KL4/1, KL4/16, KL4/17, KL4/23, KL4/28, KL4/29, KL4/4, KL4/8, KD4/6G, HO4/2, HO4/18, NR4/4 Front axle models: AL3/1, AL3/2, AL3/3, AL3/4, AL3/7, AL3/8
GO1329 - Hub Nut Socket - Polygonal - R.O.R
Technical data: Octagon 127 mm Ø 126 mm Application: Suitable for R.O.R.
GO1328 - Hub Nut Socket - Mercedes
Technical data: 6-teeth - tooth width 7,5 mm Inner Ø 101 mm - Sq 1” Application: Suitable for MERCEDES ATEGO
GO1327 - Hub Nut Socket - TGA/MAN
Technical data: 6-teeth - tooth width 8 mm Inner Ø 92,5 mm - Sq 1” Application: Front axle models: TGA V9 - 82L - 01 Suitable for MAN
GO1326 - Hub Nut Socket - TGA/MAN/Mercedes
Technical data: 6-teeth - tooth width 11,5 mm Inner Ø 117 mm - Sq 1” Application: Rear axle models: TGA Suitable for MERCEDES, MAN
GO1325 - Hub Nut Socket - Polygonal - Iveco
Technical data: Polygon 85 mm Inner Ø 83 mm - Sq 1” Application: Suitable for IVECO
GO1324 - Hub Nut Socket - Hexagonal - S.A.F
Technical data: Hexagon 140 mm - Sq 1” Application: Suitable for S.A.F.
GO528 - Heavy Duty Suspension Hook
For use with GO520 & GO530 Heavy Duty Suspension Hook for use with slide hammers when repairing axles and bodywork The extra wide version is ideal for loosening connections on the wishbone (ball joint / clamping bore) and wheel bearing housing with inserted spring struts Also ideal for straightening work on columns A, B or C due to the bracket profile Technical data: Connection thread: M18x1.5 Internal height: 110 mm Hook Width: 40 mm Total weight: 2.34 kg Applications Include Ford Mondeo, Mercedes-Benz Vito front axle etc.
GO384 - Shock Absorber Strut Tool with Oval Pin
Ideal for retaining the shock absorber strut during the assembly and disassembly phase of the rear shock absorber upper support. It lets you hold the piston strut up when loosening the fixing nut on the bearing of the support Suitable for all shock absorbers with oval pin With 2 different sizes per tool: 5x8mm and 6x9mm Safer and easier to handle than locking pliers For use on VW, Ford, Opel and Audi Vehicles
GO101 - Press Frame / C-Clamp Support For Use with Transmission Jacks
Compatible with 18780500 Universal C-Clamp Allows the clamping of press frames and C-frame to be placed on a transmission jack Greatly facilitates the positioning of the components press frames when replacing bearings, bushings, load-bearing joints, etc. directly on the vehicle This tool can be adjusted and rotated. The press frames can be placed between the jaws Use with GO102 to suit transmission jacks from other manufacturers Base diameter - 40.6mm Technical data: Pit lift housing: 40mm Total length: 220mm