Hub Puller

60 products

  • 150000V2 1500 Series 8 Tonne Hydraulic Ram

    150000V2 1500 Series 8 Tonne Hydraulic Ram

    New design includes pre-loading 30mm hex, 2” extension and foam cut out for storage. Standard power unit for SP hydraulic pulling options and can also be used with many alternative SP puller applications e.g. 3 leg pullers, ball joint pullers, hub pullers, suspension bush removers etc Diameter 1 1/2" Thread 16tpi Whitworth Grease filled. Direct force improves stability under load. Provides maximum withdrawal force of 80kN. New hex head makes it possible to increase pre-load capability up to 4 tonnes (with the use of a 30mm wrench). When hydraulic power is applied, the full force is achieved with little loss of ram travel. As the workpiece starts to release, more stroke and power can be applied to ensure a good safe removal.  

  • 180000V2 1800 Series 12 Tonne Hydraulic Ram

    180000V2 1800 Series 12 Tonne Hydraulic Ram

    NEW DESIGN UPGRADE - NOW INCLUDES PRE-LOADING 30MM HEXIncludes: 2” extension and foam cut-out for storage Standard power unit for SP suspension products and is 50% more powerful than the original SP1500 Series 8 tonne ram, creating reliable power for tough applications Can achieve up to 4 tonnes of mechanical force prior to hydraulic operation Diameter 1 1/2" Thread 16tpi Whitworth N.B. Due to the thread being the same as the 1500 series ram it can be used with our hydraulic puller range but all of the components in that range are rated at 10T and so if you chose to use this ram it is at your own risk and Sykes Pickavant cannot be held responsible for any accidents or component damage

  • Hub Puller Spares- Threaded Centre Rod

    210275-27 Threaded Centre Rod

    Threaded Centre Rod for 21027500 HGV Hub Puller Kit

  • M22 x 1.5 Thread Adaptor

    210275-07 M22 X 1.5 Thread Adaptor

    M22 X 1.5 Thread Adaptor for 21027500 HGV Hub Puller Kit

  • Master Hub Puller Plate Kit

    08522500 Master Hub Puller Plate Kit

    Universal hub puller plate with 8 slots for maximum coverage Full kit with all options  Hydraulic / slide hammer / force screw  Supplied in metal tin 

  • 08251900 Shock Handle

    08251900 Shock Handle

    Use in conjunction with 12731100 Impact Force Screw - allows for greater force to be applied When used together, Shock handle (08251900) and Impact Force Screw (12731100) can convert 1500 series hydraulic rams to mechanical. In addition the impact shock handle to screw has a sliding centre spindle which allows the operator to strike the end when fully loaded. This assists the release of stubborn joints or taper fits.

  • GO439 Double Cone Bearing Removal Kit

    GO439 Double Cone Bearing Removal Kit

    For the quick removal of wheel hubs and bolted wheel bearings. Simple and efficient method to remove front wheel hubs quickly and without too much effort in terms of assembly. The new slide hammer version is filled with steel shot. This prevents the weight from bouncing back against the stop. The impact intensity is thus increased because the full impact force is transmitted to the component to be removed. Slide hammer technical data: Weight: 3Kg Total length: 580mm Connection - Thread: M18x1.5   Applications: Injectors Hubs Support joints Bodywork works

  • GO521 Thread Adaptor Set

    GO521 Thread Adaptor Set

    Mounting unit for Heavy Duty Slide Hammer - GO520 Supplied with 4 x commonly used slide hammer adaptors  1 x system adaptor tool, M18 x 1.5 with mounting bore (jointed connection) for universal hooks, double extractor hooks, bow hooks, bodywork pull clamps etc. Suitable for Muller /Klann /KS /Pichler 1 x system adaptor tool, M18x1.5/1-1/2 inch x 16 for wheel hub puller. Suitable for Muller /KS /Pichler 1 x universal adaptor with ball joint, M18x1.5, for use between the slide hammer and the tool, enables work in hard-to-reach places. Suitable for all systems 1 x system adaptor tool, M18 x 1.5/M22x2.0, for wheel hub puller. Suitable for Facom

  • GO530 Slide Hammer - 9KG Non-Impact

    GO530 Slide Hammer - 9KG Non-Impact

    For powerful expulsion of stuck components as well as for body straightening work. The new slide hammer version is filled with a steel shot. This prevents the weight from bouncing back against the abutment. The impact intensity is thus increased because the full impact force is transmitted to the component to be machined. This version is also very gentle on the joints and allows fatigue-free working. The tool is modular and can be split and used as 1.5 kg sliding hammer. The slide hammer is filled with a steel shot. The range of applications can be increased as desired through the optional purchase of additional accessories!   Applications Removal of injectors/wheel hubs/ suspension joints Straightening and reverse deformation of body parts etc.   Technical data Weight 9 kg Total length 770 mm Connection “ Thread M18x1,5; M22x2,0

  • GO520 Heavy Duty Slide Hammer

    GO520 Heavy Duty Slide Hammer

    For driving out components and straightening jobs on bodywork with extra tough heavy-duty design and practical handles 8 tonne (approx.) maximum force Loosens even the tightest connections; pressed or rusted in / attached with a cone Suitable for removing injectors, wheel hubs, supporting joints etc. with relevant accessories Specifications: Weight: 9kg Length: 770mm Connection Thread: M18 x 1.5

  • GO1061 17T Hydraulic Cylinder - Aluminium

    GO1061 17T Hydraulic Cylinder - Aluminium

    The mechanical properties, the shape and dimensioning for which they were designed, ensure that Govoni hydraulic cylinders have a field of use to the automotive industry as: Injector disassembly; Bearing, hub and silent block disassembly; Coaxial unlocking of very tight mechanical components. Equipped with 5 threaded bushes in order to fit the most relevant threaded bars on the market. Operation/Working with hydraulic pump, GO1030.   Technical Data: Provides up to 17 tons of controlled hydraulic force Dimensions: Ø90 x 155 mm Stroke: 43 mm Pressure: max. 700 Bar Connection: 3/8œ -18 NPT Mounting Thread: 2 3/4-16 UN Adaptors: M10 / M12 / M14 / M16 / M18

  • GO070 Spacer and Extension Set

    GO070 Spacer and Extension Set

    Upgrade kit for the GO010 Universal Hub Puller and Drive Shaft SetThis kit ensures a strong flange connection with the hub and is also suitable for systems with wheel nuts and/or bolts. The user is not bound to the diameter of the hub edge since the hub's flange is placed 80mm or 90mm in front of the hub.Contents: 1 x Bolt adapter-set M12x1.25, 5pcs. 1 x Bolt adapter-set M12x1.50, 5pcs. 1 x Bolt adapter-set M14x1.50, 5pcs.

  • GO011 Drive Shafts and CV Joint Set

    GO011 Drive Shafts and CV Joint Set

    Upgrade kit for the GO010 Universal Hub Puller and Drive Shaft SetUse this kit if the profile of the seat of the drive shaft's spline has a high degree of adjustment with respect to the profile of the seat of the hub's spline. The adapters in this kit can be used both on drive shafts secured with nuts (of commercial use) and those secured with bolts (VW/Audi for example). This set is also suitable for fitting the hub.   Applications:VW/Audi/Seat/Skoda/BMW/Mercedes/Opel/Renault/Peugeot/Porsche (Cayenne) etc. Contents: 10 x pieces for traction sockets for outer thread drive shaft, M16 x 1.5 / M18 x 1.5 / M20 x 1.0 / M20 x 1.25 / M20 x 1.5 / M20 x1.0 / M22 x 1.5 / M24 x 1.5 / M27 x 1.5 / M30 x 1.5 2 x pieces for tie rods for inner thread-drive shaft, M14 x 1.5 / M16 x 1.5 1 x piece for adaptor-fitting M12 x 1.25 /  M16 x 1.5 1 x piece for thrust screw M16 / M12, L=300 mm 1 x piece for bell-hub support, 1-1/2"x16 G 1 x piece for support bushing with thrust bearing 1 x piece for nut-traction M16 2 x pieces for adaptors to remove the joints from the drive shaft

  • GO020 Inner Bearing Replacement Kit

    GO020 Inner Bearing Replacement Kit

    Universal tool set for the replacement of inner bearings. Puller features a unique gripping principle that can also be used on flush bearing inner rings that remain on the wheel hub duringreplacement of the wheel bearing. When clamping with the clamping bell, the special cutting profile of the clamping sleeves penetrates even the smallest working gaps resulting from theproduction process, ensuring removal without slippage. The bearing ring is fully gripped and removed without tilting. Also works in places where the ABS pulse wheel is firmly attached to the wheel hub (e.g. VW Golf). Supplied with 5 grippers suitable for the removal of bearings with a diameter of 35 to 61mm Applications: VW, Audi, BMW, Ford, Fiat, Mercedes, Opel, Renault, Peugeot & Volvo. The kit includes the bushing for mounting the mechadraulic screw (GO1016).

  • GO010 Universal Hub Puller and Drive Shaft Set - Basic

    GO010 Universal Hub Puller and Drive Shaft Set - Basic

    For pressing out seized and bonded drive shafts and also, with the optional Govoni slide hammer GO421, for removing the wheel hub Considerable time savings - no damage to the thread - wheel bearing is not damaged Optimised hole pitch for maximum coverage of models within the market Suitable for 2, 3, 4, 5 and 6-hole bolt pitch on hubs with stud bolts and wheel boltsContents:  1 x extractor with mounting thread 1-1/2œ-16G 1 x reducing adapter ring for mechanical spindle,1-1/2œ-16G x M22x2.0 1 x mechanical spindle, M22x2 1 x pulling flange, 96-142 mm for 3, 4, 5 and 6- holebolt hub, for M12/M14 bolts 5 x conical washers 1 x solid lubricant paste

  • 95mm Pressure Plate

    210275-10 95mm Pressure Plate

    95mm Pressure Plate for 21027500 HGV Hub Puller Kit

  • 90mm Pressure Plate

    210275-12 90mm Pressure Plate

    90mm Pressure Plate for 21027500 HGV Hub Puller Kit

  • 110mm Pressure Plate

    210275-11 110mm Pressure Plate

    110mm Pressure Plate for for 21027500 HGV Hub Puller Kit

  • Hub Puller Spares- Beam

    210275-13 Beam

    Beam for 21027500 HGV Hub Puller Kit

  • M22 - 7/8 14UNF Thread Adaptor

    210275-09 M22 - 7/8 14UNF Thread Adaptors

    M22 - 7/8 14UNF Thread Adaptors for 21027500 HGV Hub Puller Kit

  • M22- 7/8 11BSF Thread Adaptors

    210275-08 M22 - 7/8 11BSF Thread Adaptors

    M22 - 7/8 11BSF Thread Adaptors for for 21027500 HGV Hub Puller Kit

  • M20 x 1.5 Thread Adaptors

    210275-06 M20 X 1.5 Thread Adaptors

    M20 X 1.5 Thread Adaptors for 21027500 HGV Hub Puller Kit

  • M22 x 2.5 Nut

    210275-04 M22 X 2.5 Nut

    M22 X 2.5 Nut for 21027500 HGV Hub Puller Kit

  • 340mm Pulling Rod

    210275-03 340mm Pulling Rod

    340MM M22 X 2.5 & M22 X 1.5 Pulling Rod for 21027500 HGV Hub Puller Kit

  • M18 x 1.5 Thread Adaptors

    210275-05 M18 X 1.5 Thread Adaptors

    M18 X 1.5 Thread Adaptors for 21027500 HGV Hub Puller Kit

  • 20880000 HGV Hydraulic Wheel Puller

    20880000 HGV Hydraulic Wheel Puller

    Designed specifically for the removal of 10 stud 22.5 HGV wheels Pulls inner and outer wheels on twin or single wheel hubs 12 tonne hydraulic force dislodges the most difficult of seized rims Suitable for alloy or steel wheels (soft coated hook sets required for use on alloy wheels) Features: 12 tonne hydraulic ram system 2 Spigot ring sizes for most popular applications “ 281mm & 221mm 4 high strength chains 2 hook types specially designed for internal and external pulling applications Supplied in metal case Includes: 1 x 12T Self Contained Hydraulic Ram 1 x Main Beam 4 x Chains C/W Clevis Pins  4 x Hook - Internal 4 x Hook - External  1 x Pusher Ring Large 1 x Pusher Ring Small 4 x Connecting Rods 1 x Spigot Bung Assembly 1 x Metal Box 1 x Trolley *Soft coated hooks shown but not supplied - available separately 

  • 09595000 M6 - M20 Threaded Stud Extractor

    09595000 M6 - M20 Threaded Stud Extractor

    For the extraction of tapped dowels from their location holes Kit includes Slide Hammer & Adaptors   Contents: ½ UNF Slide Hammer 3/8 Convertor 5/8 Convertor M6 x 1mm Adaptor M8 x 1.25mm Adaptor M10 x 1.5 Adaptor M12 x 1.75mm Adaptor M14 x 2mm Adaptor M16 x 2mm Adaptor M18 x 2.5 Adaptor M20 x 2.5mm Adaptor

  • 09600000 6 - 16mm Dowel Pin Puller Set

    09600000 6 - 16mm Dowel Pin Puller Set

    Tapered collets thread onto stud, even where only a few threads are exposed The collet is drawn into the housing and clamped onto stud by tightening the housing bolt Reduces possibility of damage to stud threads Prevents shearing or damaging stud/ workpiece by avoiding bottoming or shouldering studs 6 collet sizes; 6mm, 8mm, 10mm, 12mm, 14mm & 16mm

  • 095950-20 5/8" - M20 Adaptor

    095950-20 5/8" - M20 Adaptor

    5/8" - M20 Adaptor for 09595000 - M6 - M20 Threaded Stud Extractor

  • 095950-16 5/8" - M16 Adaptor

    095950-16 5/8" - M16 Adaptor

    5/8" - M16 Adaptor for 09595000 - M6 - M20 Threaded Stud Extractor

  • 095950-18 5/8" - M18 Adaptor

    095950-18 5/8" - M18 Adaptor

    5/8" - M18 Adaptor for 09595000 - M6 - M20 Threaded Stud Extractor

  • 095950-14 5/8" - M14 Adaptor

    095950-14 5/8" - M14 Adaptor

    5/8" - M14 Adaptor for 09595000 - M6 - M20 Threaded Stud Extractor

  • 095950-12 5/8" - M12 Adaptor

    095950-12 5/8" - M12 Adaptor

    5/8" - M12 Adaptor for 09595000 - M6 - M20 Threaded Stud Extractor

  • 095950-10 3/8" - M10 Adaptor

    095950-10 3/8" - M10 Adaptor

    3/8" - M10 Adaptor for 09595000 - M6 - M20 Threaded Stud Extractor

  • 095950-08 3/8" - M8 Adaptor

    095950-08 3/8" - M8 Adaptor

    3/8" - M8 Adaptor for 09595000 M6 - M20 Threaded Stud Extractor

  • 095950-06 3/8" - M6 Adaptor

    095950-06 3/8" - M6 Adaptor

    3/8" - M6 Adaptor for 09595000 - M6 - M20 Threaded Stud Extractor

  • 095950-02 1/2" / 5/8" Adaptor

    095950-02 1/2" / 5/8" Adaptor

    1/2" / 5/8" Adaptor for 09595000 - M6 - M20 Threaded Stud Extractor

  • 09590000 M4 - M10 Threaded Stud Extractor

    09590000 M4 - M10 Threaded Stud Extractor

    For the extraction of tapped dowels from their location holes Kit includes Slide Hammer & Adaptors   Contents: M10 Slide Hammer  M4 Adaptor M5 Adaptor M6 Adaptor M8 Adaptor

  • 095900-08 M8 Adaptor

    095900-08 M8 Adaptor

    M8 Adaptor for 09590000 - Threaded Stud Extractor

  • 095900-06 M6 Adaptor

    095900-06 M6 Adaptor

    M6 Adaptor for 09590000 - Threaded Stud Extractor

  • 095950-01 1/2" / 3/8" Adaptor

    095950-01 1/2" / 3/8" Adaptor

    1/2" / 3/8" Adaptor for 09595000 - M6 - M20 Threaded Stud Extractor

  • 095900-04 M4 Adaptor

    095900-04 M4 Adaptor

    M4 Adaptor for 09590000 Threaded Stud Extractor

  • Hub Puller Plate Adaptor
  • 095900-05 M5 Adaptor

    095900-05 M5 Adaptor

    M5 Adaptor for 09590000 - Threaded Stud Extractor

  • 08100000 universal bearing ring puller

    08100000 universal bearing ring puller

    WHEEL BEARING REMOVAL & INSTALLATION For the removal of bearings, races, sleeves etc Ideal tool for the removal of bearing rings from hubs, axles etc Removes the need for cutting tools - greatly reduces bearing ring removal time Unique patented design - specially designed cutting edges on puller legs Legs ut and are pressed into the radius behind the bearing ring ˜Loose / Tight pulling principal means force is applied evenly at all points on the bearing ring Suitable for all types of bearings and rings from 40 - 60mm diameter Supplied in plastic toolbox for safe storage Specification: Spread: 40-60mm Reach: 85mm  

  • Hub Puller Plate

    08520800 Hub Puller Plate

    Universal hub puller plate with 8 slots for maximum coverage

  • 1500MERCH Series 8 Hydraulic Rams and Merhandiser

    1500MERCH Series 8 Hydraulic Rams and Merhandiser

    Includes pre-loading 30mm hex, 2” extension and foam cut out for storage Standard power unit for SP hydraulic pulling options and can also be used with many alternative SP puller applications e.g. 3 leg pullers, ball joint pullers, hub pullers, suspension bush removers etc. 1 1/2” thread Grease filled Direct force improves stability under load Provides maximum withdrawal force of 80kN New hex head makes it possible to increase pre-load capability up to 4 tonnes (with the use of a 30mm wrench) When hydraulic power is applied, the full force is achieved with little loss of ram travel As the work-piece starts to release, more stroke and power can be applied to ensure a good safe removal  Includes 5 Hydraulic Rams and Desktop Merchandiser

  • 17700000 Large Universal Internal / External Puller

    17700000 Large Universal Internal / External Puller

    Large Capacity Universal Puller Kit Suitable for applications with a large span Includes two pairs of setting sleeves to ensure pulling length is equal for each leg; less time is spent levelling nut position Use of the puller without setting sleeves is possible however more care is needed to guarantee successful levelling Suitable for use with air tools Internal / external reversible legs - can also be used for internal applications Ideal for use on bearings, gears and brake discs   Dimensions: Reach: 295mm with 1 setting sleeve 340mm with 2 setting sleeves 250 - 340mm with no setting sleeves   Spread: 0mm - 400mm   

Hub Puller

Login

Forgot your password?

Don't have an account yet?
Create account