Govoni

Allows for the assembly/disassembly of the brake caliper fixing screws when working on the braking system. Used mainly on the front and rear axles of heavy vehicles. Even the most stubborn screws are released with the blow of a hammer on the end of the wrench. All wrenches are equipped with a ¾" square drive that also allows clamping, in combination with a torque wrench, according to the manufacturer's instructions. Warning: pay attention to the torque conversion formula marked on the wrench by means of a laser (necessary because of the lever's extension due to the type of construction). It is no longer necessary to remove the lever of the steering control tie rod.   Application: MB Atego, Actros/Kässbohrer Bus   Technical data: Length: 220mm 6-side profile

Read more less

To loosen and tighten fuel filters and oil filters. The wrench is equipped with 2 extension half-shells (toothed on the inside), which are attached directly to the jaws of the filter wrench and can be secured in place. It can be used with or without extensions. Can be used for filters with and without guide profiles Ø 60-80 with extension

Read more less

Allows for the assembly/disassembly of the brake caliper fixing screws when working on the braking system. Used mainly on the front and rear axles of heavy vehicles. Even the most stubborn screws are released with the blow of a hammer on the end of the wrench. All wrenches are equipped with a ¾" square drive that also allows clamping, in combination with a torque wrench, according to the manufacturer's instructions. Warning: pay attention to the torque conversion formula marked on the wrench by means of a laser (necessary because of the lever's extension due to the type of construction). It is no longer necessary to remove the lever of the steering control tie rod.   Application: MAN TGL Technical data: Length: 219mm Hex profile

Read more less

Allows for the assembly/disassembly of the brake caliper fixing screws when working on the braking system. Used mainly on the front and rear axles of heavy vehicles. Even the most stubborn screws are released with the blow of a hammer on the end of the wrench. All wrenches are equipped with a ¾" square drive that also allows clamping, in combination with a torque wrench, according to the manufacturer's instructions. Warning: pay attention to the torque conversion formula marked on the wrench by means of a laser (necessary because of the lever's extension due to the type of construction). It is no longer necessary to remove the lever of the steering control tie rod.   Application: MB Atego/Actros, SAF Technical data: Length: 219mm Bi-hex profile

Read more less

Easy fitting and mounting of wheels Especially dedicated for cars with short axle tie with free turning brake disc without centering screw Bolts are placed into the wheel bolt holes Very quick mounting without any thread For wheel bolts M12 and M14 Advantages:  1.   Free mounting of the wheel locking boltsThe full weight is resting on the centering bolts which allows for 2.  No risk of heavy wheels falling; decreasing the likelihood of injury to the operator Contents: 1 x Fit up bolt M12 x 127.5 mm1 x Fit up bolt M14 x 127.5 mm2 x Replacement sleeve M12 x 27.8 mm2 x Replacement sleeve M14 x 27.8 mm1 x support

Read more less

This tool is universally used for light and heavy diesel engines, this tool allows you to professionally restore the thread of the NOx sensor hole without damaging the exhaust system.  The tool is equipped with an alignment guide at the front of the male threader to ensure a correct angle. With an extra short body, the tool can be used with a socket wrench or ratchet wrench in tight spaces. Optimal for cleaning and regenerating threads up to the end of the thread/stop blind hole. Application Audi, Vw, Porsche, Opel, Mercedes-Benz, Bmw, General Motors, Man Technical data Square Drive: SW 13 mm Length: 50 mm Tensioning grooves: 6 Material: HSCO

Read more less

Application Citroen, Opel, Peugeot, Toyota: 9819074780, SU001 A6528 FAG: 713 6506 80 SKF: VKBA 7120

Read more less

Use this tool kit to remove and refit slotted bushes properly. The slight conical grinding makes it possible to extract and reuse bushes without damage. The tools may be fit directly on the vehicle without removing entire axes components. Pressers may also be used on the workshop press. By means of the locking device and relating half-shells, bushes are pre-tensioned carefully and parallel to one another so they can be pressed easily into their seat. While the bush is often damaged using commercial tapered sockets, the assembly operations do not damage/deform/detach the bearing's cover when this locking device system is used. The half-shells are fixed securely inside the locking device so they will not slip out. The kit includes a wide selection of the most common applications with high market coverage. Other half-shell kits will soon follow to ensure the subsequent removal of the system. Due to the partly enormous forces required especially for removal, the kit includes GO1012 12T Hydraulic cylinder , which is optimal for integrations.   20017000 Hand Operated Hydraulic Aluminium Pump is required in order to operate the kit Application Ø 75mm MB Actros (stabilizer) Ø 70mm MAN Ø 68mm MAN (front spring) ROR, SAF Ø 66mm IVECO Eurostar (driver’s cabin) Ø 65mm MB Actros (stabilizer), Atego Ø 63mm DAF Ø 60mm MB/IVECO Eurostar (stabilizer), Renault Kerax, Magnum, Premium (leaf spring eye) Ø 58mm MB 3229 B, 652, 650/Volvo Ø 56mm IVECO Eurostar (driver’s cabin)

Read more less

Locking Pliers supplied with 4 sets of interchangeable clamps for tightening the snap ring on the transmission shaft.  There pliers ensure mounting without risk of damage to the rush (clips) of the teeth when inserting the bowl on the transmission shaft.  Includes:  1 x Pliers 2 x Ø23.8mm half shell 2x Ø24.6mm half shell  2x Ø26.9mm half shell 2x Ø28.5mm half shell

Read more less

They allow for the assembly/disassembly of the brake caliper fixing screws when working on the braking system. Used mainly on the front and rear axles of heavy vehicles. Even the most stubborn screws are released with the blow of a hammer on the end of the wrench. All wrenches are equipped with a ¾" square drive that also allows clamping, in combination with a torque wrench, according to the manufacturer's instructions. It is no longer necessary to remove the lever of the steering control tie rod.  Application: MB Atego, Actros/Kässbohrer Bus  Technical data: Length: 220mm 6-side profile

Read more less

Technical data: CH. 41 mm  Octagonal 80,5mm   Application: Suitable for SCANIA

Read more less

Due to the particular shape of the arms, these pliers allow you to easily open and close CAILLAU CLIC (55, 66, 86), CLIC R (R66, R86, R96) and CLIC E clamps With these pliers it is possible to open and close screwless hose clamps It is possible to change from the opening to the closing function by rotating the pliers 180° Ergonomic, self-opening handles with different colours to identify the opening and closing functions For vehicle engine and chassis, fuel lines, air filters, steering, drive shaft sleeves, as well as other industrial and electrical sectors

Read more less

 It is possible to remove the drive shaft inserted in the gearbox, with the use of this tool Insert the tool between the drive shaft and gearbox. Then, with a slight slide hammer hit, the fixing circlip, found in the gearbox, is broken The difficult position of the fixing circlip is avoided by the forks central traction, allowing the user to easily unlock the drive shaft

Read more less

Universal lifting table with a load capacity of 1500kg (1.5T) Aside from lifting electric-car batteries, this product is also perfect for lifting and moving engines, automatic gearboxes, chassis components Features: Powered by compressed air. Sliding cover, allowing convenient battery installation or removal. High ground clearance makes it compatible with all workshop cranes on the market. Extendable and tiltable top table, by means of a mechanical screw Easy to operate and tilt with self explanatory operations. The table features holes with M10 thread, which can be used to mount all types of supports or accessories, including special hooks, brackets, and protective mats for battery packs. Button operated table lowering Rack safety system, when not being operated, the table locks by means of a mechanical anti-lowering safety wedge. Specifications Opening Table                       - Extendable Table                   (200mm) Tilting Table                           (±3°) Shifting Table                        - Extendable Handle               - Fork Housing                        OK Max Capacity                        1500 KG Time To Go Up                      80 s (no load) / 150 s (full load) Time To Go Down                 70 s (no load) / 15 s (full load) Power Supply                       6/8 bar

Read more less

Universal lifting table with a load capacity of 1500kg (1.5T) Aside from lifting electric-car batteries, this product is also perfect for lifting and moving engines, automatic gearboxes, chassis components   Features: Powered by compressed air. Sliding cover, allowing convenient battery installation or removal. High ground clearance makes it compatible with all workshop cranes on the market. Extendable and tiltable top table, by means of a mechanical screw Table top can be moved laterally up to 30mm to allow repositioning under the vehicle. Easy to operate and tilt with self explanatory operations. The table features holes with M10 thread, which can be used to mount all types of supports or accessories, including special hooks, brackets, and protective mats for battery packs. Button operated table lowering Rack safety system, when not being operated, the table locks by means of a mechanical anti-lowering safety wedge.   Specifications Opening Table                      - Extendable Table                  (200mm) Tilting Table                          (±3°) Shifting Table                        (±30mm) Extendable Handle               (225mm) Fork Housing                        OK Max Capacity                        1500 KG Time To Go Up                      80 s (no load) / 150 s (full load) Time To Go Down                 70 s (no load) / 15 s (full load) Power Supply                       6/8 bar  

Read more less

Induction heating is a non-contact method that can be used to heat metals. The induction heater creates an alternating magnetic field that generates induced currents within the material. It is these induced currents that generate heat. The absence of open flames makes work easier, while ensuring safety and economic savings at the same time. It allows you to work even close to heat-sensitive parts Heat inductors are ideal for a wide range of applications such as: Unlocking bolts/nuts Unlocking and replacing pins or bearings Heating for straightening Preheating before welding Bending Thermal treatments  Advantages: Power level setting (KW) Keyboard Inductor cable 3M Ready to use with tip  Technical data Input power 5 KW-16 A, electrical connection IEC60309 Voltage 220V 1PH+T 50 Frequency level 15-30khz Work cycle 30 min* (*± 5% ambient temperature maximum power) 8m of electrical cable IP21 protection rating Protection fuses 20 litre tank capacity with liquid cooling system Hydraulic heat exchanger with fan

Read more less

Induction heating is a non-contact method that can be used to heat metals. The induction heater creates an alternating magnetic field that generates induced currents within the material. It is these induced currents that generate heat. The absence of open flames makes work easier, while ensuring safety and economic savings at the same time. It allows you to work even close to heat-sensitive parts Heat inductors are ideal for a wide range of applications such as: Unlocking bolts/nuts Unlocking and replacing pins or bearings Heating for straightening Preheating before welding Bending Thermal treatments  Advantages: Power level setting (KW) Keyboard Inductor cable 3M Ready to use with tip  Technical data Input power 5 KW-16 A, electrical connection IEC60309 Voltage 400V 3PH+T 50 Frequency level 15-30khz Work cycle 30 min* (*± 5% ambient temperature maximum power) 8 m of electrical cable IP21 protection rating Protection fuses 20 litre tank capacity with liquid cooling system Hydraulic heat exchanger with fan

Read more less

Induction heating is a non-contact method that can be used to heat metals. The induction heater creates an alternating magnetic field that generates induced currents within the material. It is these induced currents that generate heat. The absence of open flames makes work easier, while ensuring safety and economic savings at the same time. It allows you to work even close to heat-sensitive parts Heat inductors are ideal for a wide range of applications such as: Unlocking bolts/nuts Unlocking and replacing pins or bearings Suspension, shock absorbers & mufflers removal Bending Crankshaft straightening  Advantages: Compact dimensions Power level setting (KW) Keyboard Inductor cable 2M Ready to use with tip  Technical data Input power 3.5 KW-16 A, IEC60309 electrical connection Voltage 230V/1PH - 50/60 Frequency level 15-30khz Duty cycle 5 min* (*± 5% ambient temperature maximum power) 2m of electrical cable Protection fuses 1 litre tank capacity with liquid cooling system Hydraulic heat exchanger with fan

Read more less

Technical data: CH. 105,4 mm - depth 38 mm - Sq 1”   Application: Suitable for RENAULT, VOLVO, FIAT, DAF

Read more less

Induction heating is a non-contact method that can be used to heat metals. The induction heater creates an alternating magnetic field that generates induced currents within the material. It is these induced currents that generate heat. The absence of open flames makes work easier, while ensuring safety and economic savings at the same time. It allows you to work even close to heat-sensitive parts  Heat inductors are ideal for a wide range of applications such as: Unlocking bolts/nuts Unlocking and replacing pins or bearings Heating for straightening Preheating before welding Bending Thermal treatments  Advantages: Electronic safety protection Level heating temperature setting Easy to use 5" colour touch control panel Inductor cable 4.5M Ready to use with tip  Technical data: Input power 18 KW-32 A, electrical connection IEC60309 INVERTER generator Voltage 400V 3PH+T 50 Frequency level 15-30khz 8 m of electrical cable IP21 protection rating Protection fuses 20 litre tank capacity with liquid cooling system Hydraulic heat exchanger with fan

Read more less

Technical data: 6-teeth - tooth width 9,8 mm Inner Ø 113 mm - ☐ 1”   Application: Axle models: NS4/2 - NS4/10 Sprocket axle models: HL6/1, HL6/2, HL6/3, HD6/3

Read more less

Induction heating is a non-contact method that can be used to heat metals. The induction heater creates an alternating magnetic field that generates induced currents within the material. It is these induced currents that generate heat. The absence of open flames makes work easier, while ensuring safety and economic savings at the same time. It allows you to work even close to heat-sensitive parts Heat inductors are ideal for a wide range of applications such as: Release of highly corroded or seized bolts/nuts Unlocking and replacing pins or bearings Heating for straightening Preheating before welding Bending Thermal treatments  Advantages: Electronic safety protection Level heating temperature setting Easy to use 5" colour touch control panel Inductor cable 4.25M Ready to use with tip  Technical data Input power 13 KW-32 A, electrical connection IEC60309 INVERTER generator Voltage 400V 3PH+T 50 Frequency level 15-30khz 8 m of electrical cable IP21 protection rating Protection fuses 20 litre tank capacity with liquid cooling system Hydraulic heat exchanger with fan

Read more less

SPARE TIP FOR GO1474 INDUCTION HEATER

Read more less

Induction heating is a non-contact method that can be used to heat metals. The induction heater creates an alternating magnetic field that generates induced currents within the material. It is these induced currents that generate heat. The absence of open flames makes work easier, while ensuring safety and economic savings at the same time. It allows you to work even close to heat-sensitive parts Heat inductors are ideal for a wide range of applications such as: Unlocking bolts/nuts Unlocking and replacing pins or bearings Heating for straightening Preheating before welding Bending Thermal treatments  Advantages: Electronic safety protection Easy to use 5" colour touch control panel Inductor cable 3M Ready to use with tip  Technical data Input power 8 KW-16 A, electrical connection IEC60309 INVERTER generator Voltage 230V 3PH+T 50 Frequency level 15-30khz 8 m of electrical cable IP21 protection rating Protection fuses 20 litre tank capacity with liquid cooling system Hydraulic heat exchanger with fan

Read more less

Replacement ferrite piece for wand used with Govoni Induction Heaters

Read more less

Technical data: Hexagonal nut 95 mm - Sq 1”   Application: Rear axle Trailer axle Axle with compact bearings

Read more less

Technical data: 12-teeth - tooth width 8 mm Inner Ø 90 mm - Sq 1”   Application: BRG year 2001 Suitable for MERCEDES ACTROS 1840

Read more less

Technical data: Hexagon 160 mm -  Sq 1”   Application: Suitable for FONTENAC RENAULT

Read more less

Technical data: 6-teeth - tooth width 10 mm Inner Ø 77 mm - Sq 1”   Application: Front axle models: VW2 - VW4 - VW6.1 - 6.8 Suitable for MAN

Read more less

Technical data: 6-teeth - tooth width 10,9 mm Inner Ø 71,5 mm - Sq 3/4”   Application: Rear axle models: HL2/2, HL2/7, HL2/13

Read more less

Allows the separation and disassembly of twin wheels in heavy vehicles.This set offers a simple and effective solution to help you in the disassembly stages. The two rims come apart using the supports and the spindle (fixed impact screwdriver).Usually it is also possible to loosen the rear rim by placing it on the brake drum.Also ideal as a tool to take on board or for roadside assistance.This set also includes two wheel-centering pins that protect the wheel's bolts, facilitate wheel assembly and keep the brake's drum in place, in case the drum brakes.

Read more less

Allows for the assembly/disassembly of the brake caliper fixing screws when working on the braking system. Used mainly on the front and rear axles of heavy vehicles. Even the most stubborn screws are released with the blow of a hammer on the end of the wrench. All wrenches are equipped with a ¾" square drive that also allows clamping, in combination with a torque wrench, according to the manufacturer's instructions. Warning: pay attention to the torque conversion formula marked on the wrench by means of a laser (necessary because of the lever's extension due to the type of construction). It is no longer necessary to remove the lever of the steering control tie rod.   Application: DAF XF95/XF105/XF106/XF Technical data: Length: 219mm Bi-hex Profile

Read more less

Technical data Force: 12ton Stroke: 8 mm. Dimensions: 80x55 mm Pressure: max. 700 Bar Hole: 21.5 mm Connection: 3/8" -18 NPT Material: steel

Read more less

12-teeth - tooth width 10 mm - Inner Ø 102 mm 6-teeth - tooth width 10 mm - Inner Ø 99 mm  Application: Rear axle models: 10TN/13TN, HL7/1, HL7/2, HL7/18, HO7/8, H07/9, HL7/0, HL7/015, HL/021, HL7/3, HD7/2, HD7/19DG, HD7/016DG Front axle models: 7TN AL7/1

Read more less

Allows for the assembly/disassembly of the brake caliper fixing screws when working on the braking system. Used mainly on the front and rear axles of heavy vehicles. Even the most stubborn screws are released with the blow of a hammer on the end of the wrench. All wrenches are equipped with a ¾" square drive that also allows clamping, in combination with a torque wrench, according to the manufacturer's instructions. Warning: pay attention to the torque conversion formula marked on the wrench by means of a laser (necessary because of the lever's extension due to the type of construction). It is no longer necessary to remove the lever of the steering control tie rod.   Application: MAN TGM - TGL  Technical data: Length: 215mm Torx profile

Read more less

Technical data: 6-teeth - tooth width 11 mm Inner Ø 88 mm - 1”   Applications: Rear axle models: VARIO 814 - SPRINTER 616 - ATEGO HL2/43 DG 6.2

Read more less

Allows for the assembly/disassembly of the brake caliper fixing screws when working on the braking system. Used mainly on the front and rear axles of heavy vehicles. Even the most stubborn screws are released with the blow of a hammer on the end of the wrench. All wrenches are equipped with a ¾" square drive that also allows clamping, in combination with a torque wrench, according to the manufacturer's instructions. Warning: pay attention to the torque conversion formula marked on the wrench by means of a laser (necessary because of the lever's extension due to the type of construction). It is no longer necessary to remove the lever of the steering control tie rod.   Application: MAN, TGM, TGL/MAN Atego up to 9 Ton Technical data: Length: 215mm Torx profile

Read more less

Allows for the assembly/disassembly of the brake caliper fixing screws when working on the braking system. Used mainly on the front and rear axles of heavy vehicles. Even the most stubborn screws are released with the blow of a hammer on the end of the wrench. All wrenches are equipped with a ¾" square drive that also allows clamping, in combination with a torque wrench, according to the manufacturer's instructions. Warning: pay attention to the torque conversion formula marked on the wrench by means of a laser (necessary because of the lever's extension due to the type of construction). It is no longer necessary to remove the lever of the steering control tie rod.   Application: MAN TGA, TGS, TGX/MB, Atego from 12 ton, Actros Technical data: Length: 215mm Torx profile

Read more less

Extractor for removing the wiper arm from the wiper shaft Special version with adjustable fork spring Extraction spindle with aluminium turning head to prevent damage to shaft Ultra-thin fork design for usage in narrow spaces Wide radius for work on large wipers Strong design for use on blocked windscreen wipers Wide adjustment range covers different sizes Spring mechanism balances the pressure on half-fork  Technical Specifications: Screw - M10 x 1.0 Connection - SW 17 mm Fork width - 16 “ 38 mm Working height - 48 mm Weight - 0.5 kg Not suitable for use with air/impact tools.

Read more less

The mechanical properties, the shape and dimensioning for which they were designed, ensure that Govoni hydraulic cylinders have a field of use to the automotive industry as: Injector disassembly; Bearing, hub and silent block disassembly; Coaxial unlocking of very tight mechanical components. Equipped with 5 threaded bushes in order to fit the most relevant threaded bars on the market. Specifications Provides up to 12 tons of controlled hydraulic force Dimensions: 90 x 155 mm Stroke: 43 mm Pressure: max. 700 Bar Hole: 20 mm Connection: 3/" -18 NPT Mounting Thread: 2 3/4-16 UN Adaptors: M10/M12/M14/M16/M18

Read more less

The mechanical properties, the shape and dimensioning for which they were designed, ensure that Govoni hydraulic cylinders have a field of use to the automotive industry as: Injector disassembly; Bearing, hub and silent block disassembly; Coaxial unlocking of very tight mechanical components. Equipped with 5 threaded bushes in order to fit the most relevant threaded bars on the market. Specifications Provides up to 32 tons of controlled hydraulic force Dimensions: 104 x 261 mm Stroke: 50 mm Pressure: max. 700 Bar Hole: 21.5 mm Connection: 3/8" -18 NPT Inner thread: M24 x 2 Outside connection thread: 2 3/4-16 UN

Read more less

The mechanical properties, the shape and dimensioning for which they were designed, ensure that Govoni hydraulic cylinders have a field of use to the automotive industry as: Injector disassembly; Bearing, hub and silent block disassembly; Coaxial unlocking of very tight mechanical components. Equipped with 5 threaded bushes in order to fit the most relevant threaded bars on the market. Specifications Provides up to 12 tons of controlled hydraulic force Dimensions: 90 x 155 mm Stroke: 43 mm Pressure: max. 700 Bar Hole: 20 mm Connection: 3/" -18 NPT Mounting Thread: 2 3/4-16 UN Adaptors: M10/M12/M14/M16/M18

Read more less

The mechanical properties, the shape and dimension for which they were designed, ensure that Govoni hydraulic cylinders have a field of use to the automotive industry as: Injector disassembly Bearing, hub and silent block disassembly Coaxial unlocking of very tight mechanical components. Equipped with 5 threaded adaptors in order to fit the most relevant threaded bars on the market. Specifications Force: 12 Tonnes Stroke: 8 mm Dimensions: 80x50 mm Pressure: Max. 700 Bar Hole: 21.5 mm Connection: 3/8"-18 NPT Material: Aluminium Adaptors: M10/M12/M14/M16/M18

Read more less

Thanks to the use of aluminium, the cylinder combines the strength of steel with the light weight of this element. Non-slip grip on the handle. There are 4 bores on the body for fastening the cylinder. Applications include: injector removal; introduction of wheel hubs; general use in the loosening of very tight mechanical components. Technical data Force: 12tons Stroke: 8 mm Body dimensions: 98x80x50(h) mm Pressure: max. 700 Bar Hole: Ø 21,5 mm Driving torque: 56Nm Weight: 1,65 Kg Grease temperature range of use: from -25°C to 80°C Material: aluminium Adaptors: M10/M12/M14/M16/M18

Read more less

Force: 17tonnes Stroke: 43 mm Dimensions: 90x155 mm Pressure: max. 700 Bar Hole: 20 mm Connection: 3/8" -18 NPT Outside connection thread: 2" 3/4-16 UN Material: steel

Read more less

Allows application of up to 20 tons of hydraulic force which can be used to provide a controlled force in place of the mechanical effort required when using the GO410 / GO426 Technical data: Dimensions:  100 x 60 Stroke:  8 mm Pressure:  700 Bar Weight:  3,04 Kg Hole:    33 Coupling connection thread 3/8" -18 NPT

Read more less

Provides up to 32 tons of controlled hydraulic force Dimensions: 104 x 261 mm Stroke: 50 mm Pressure: max. 700 Bar Hole: 21.5 mm Connection: 3/8" -18 NPT Inner thread: M24 x 2 Outside connection thread: 2" 3/4-16 UN

Read more less

Due to the mechanical properties, shape and size, the Govoni Mechadraulic-Spindle is optimally suited for use in the automotive sector for removal and installation of wheel hubs, drive shafts,  supporting joints, tie rod heads, pitman arms, silent bearings etc. The 1-1/2 inch x 16 tpi receiving thread is one of the most commonly used special tool threads  Technical data: Force: 16 T Stroke: 20 mm Dimensions: 38 x 225 Total length: 345 Weight: 1.7 Kg Use temperature: -10°C -65°C Basic oil viscosity at 40°C  ASTM  D 445: ISO VG 150 Max. driving torque/Max. pressure: 38 Nm/2.600 Bar

Read more less